It is imperative that you ensure your spark plugs are in good condition. There’s a likely chance you will need to replace your old spark plugs several times during your ownership of a 2010 Nissan Versa. Spark plugs are one of the most vital components inside your engine as they start the entire combustion process that starts and keeps your engine running for many thousands of miles. Like most engine components, spark plugs experience wear over time and eventually need to be swapped out for new replacements, but fortunately this is a repair you can do on your own. Odds are, if you’ve found yourself here, you have no idea how to do that, or maybe you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you should need to know about your Nissan Versa’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2010 Nissan Versa
For any 2010 Nissan Versa, you can use DENSO 4711 spark plugs. These will be an exact fit and will match the required specifications of your engine. As this 2010 Nissan Versa features a 4 cylinder engine, ensure you purchase 4 spark plugs. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at an affordable price.
How often should I change my spark plugs?
As a general recommendation, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Nissan for the 2010 Versa. Of course, if you drive your vehicle more aggressively or own a Versa with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that needs a spark plug replacement prematurely, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
As a quick note, keep in mind that this list is certainly not comprehensive, and these problems on their own do not definitively point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with regular maintenance, and you are definitely doing so with the responsible decision to replace your Nissan Versa’s spark plugs on a regular basis.
Changing spark plugs on a 2010 Nissan Versa
This is a process you can do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to accomplish a spark plug change with some ordinary tools you probably already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some commonplace tools that you should definitely have in your toolbox if you don’t already.
- A torque wrench is a essential tool to have in your arsenal. You should check your FSM (factory service manual) or owner’s manual to determine the correct torque rating to use when inserting the new spark plugs for your 2010 Nissan Versa to be confident they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the definite problem.
- A set of spark plug sockets – These come in very handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if not, you should for sure have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it comes in handy for countless other jobs.
Tips for changing spark plugs on your 2010 Nissan Versa
Ensure you watch the video above before you attempt to repair the spark plugs on your 2010 Nissan Versa, as well as review your FSM (factory service manual). Also, see the tips included below here to help you as you perform this repair.
- One of the most important things to remember is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- You might consider using dielectric grease when installing new spark plugs. You can apply a a very light coating to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- Note that this is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a tiny amount of anti-seize to the threads of their spark plugs, especially on older vehicles.
- Before beginning, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Nissan Versa or any other vehicle.
- Your engine should be completely cold before you replace your spark plugs. Ensure you wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 2010 Nissan Versa