There’s a decent chance you will be required to replace your old and worn out spark plugs several times during your ownership of a 2010 Jeep Liberty. Spark plugs are one of the most critical parts inside your engine as they begin the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do on your own. Chances are, if you’ve found yourself here, you have no idea how to do that, or potentially you’d just like to know what kind of spark plugs you need to buy. The entire process of changing your spark plugs should take about 20-45 minutes. This article will go over everything you will need to know about your Jeep Liberty’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2010 Jeep Liberty
AUTOLITE 5224[/caption]For any 2010 Jeep Liberty, you can use AUTOLITE 5224 spark plugs. These will be an exact fit and will match the required specifications of your engine. As this 2010 Jeep Liberty features a 6 cylinder engine, ensure you purchase 6 spark plugs. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at a reasonable price.
How often should I change my spark plugs?
In general, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Jeep for the 2010 Liberty. Of course, if you drive your vehicle more aggressively or own a Liberty with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that needs a spark plug replacement earlier than the recommended schedule, such as:
- Engine misfiring
- Problems starting your engine
- Rough idle
Consider that this list is of course not comprehensive, and these problems on their own do not definitively point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with organized maintenance, and you are definitely doing so with the responsible decision to replace your Jeep Liberty’s spark plugs on a regular basis.
Changing spark plugs on a 2010 Jeep Liberty
This is a process you should be able to do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to do a spark plug change with some regular tools you probably already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some commonplace tools that you should absolutely have in your toolbox if you do not already.
- A set of spark plug sockets – These come in very handy because many standard sockets are not deep enough for spark plugs. In addition, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the definite problem.
- A torque wrench is a very important tool to have in your arsenal. You will want to check your factory service manual to determine the correct torque rating to use when installing the new spark plugs for your 2010 Jeep Liberty to be certain they are installed properly.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and change it if necessary. Most plugs will come pregapped, but if not, you should absolutely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it comes in handy for a decent number of other jobs.
Tips for changing spark plugs on your 2010 Jeep Liberty
Please make sure you reference the video above before you attempt to repair the spark plugs on your 2010 Jeep Liberty, as well as review your FSM (factory service manual). Also, see the tips included below here to help you as you do this repair.
- First, remove the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Jeep Liberty or any other vehicle.
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- One of the most important things to remember is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- You should replace spark plugs on a cold engine. Ensure you wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2010 Jeep Liberty
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a little bit to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.