Spark plugs are one of the most critical components inside your engine that need to be maintained. There’s a likely probability you will need to replace your old spark plugs several times during your ownership of a 2007 Jeep Commander. Spark plugs are one of the most important components inside your engine as they begin the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts and components, spark plugs experience wear over time and eventually need to be replaced, but fortunately this is a repair you can do yourself. Odds are, if you’ve found yourself here, you have no idea how to do that, or perhaps you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you should need to know about your Jeep Commander’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2007 Jeep Commander
Recommended 3.7L V6 2007 Jeep Commander Spark Plugs
Recommended 4.7L V8 2007 Jeep Commander Spark Plugs
Recommended 5.7L V8 2007 Jeep Commander Spark Plugs
These spark plugs are an exact fit for their respective engines and will match the required specifications. Make certain that you purchase the correct number of spark plugs for your engine corresponding to the number of cylinders. Often, manufacturers will bundle spark plugs in quantities that make it nearly impossible to buy the exact amount you need for your engine. In this case, it is a good idea to purchase enough for your next two spark plug changes just so you will always have a new set ready. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at a reasonable price.
How often should I change my spark plugs?
As a general recommendation, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the specific interval determined by Jeep for the 2007 Commander. Of course, if you drive your vehicle more aggressively or own a Commander with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that may need a spark plug replacement early, such as:
- Problems starting your engine
- Rough idle
- Engine misfiring
As a quick note, keep in mind that this list is absolutely not comprehensive, and these problems on their own do not necessarily point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with routine maintenance, and you are definitely doing so with the responsible decision to replace your Jeep Commander’s spark plugs on a regular basis.
Changing spark plugs on a 2007 Jeep Commander
This is a process you should be able to do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to do a spark plug change with some ordinary tools you most likely already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some general tools that you should definitely have in your toolbox if you do not already.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if not, you should for sure have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it is useful for quite a few other jobs.
- A set of spark plug sockets – These come in very handy because many standard sockets are not deep enough for spark plugs. In addition, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug tester – this is definitely a niche tool, but it can save you a ton of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the exact problem.
- A torque wrench is a very important tool to have in your collection. You will want to check your FSM (factory service manual) or owner’s manual to determine the correct torque rating to use when installing the new spark plugs for your 2007 Jeep Commander to be certain they are installed properly.
Tips for changing spark plugs on your 2007 Jeep Commander
Ensure you reference the video above before you attempt to repair the spark plugs on your 2007 Jeep Commander, as well as review your FSM (factory service manual). Additionally, we have some tips below here to help you as you do this repair.
- Your engine should be completely COLD before you replace your spark plugs. Ensure you wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 2007 Jeep Commander
- You might consider using dielectric grease when installing new spark plugs. You can apply a a small dab to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- The most important thing is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- Before you begin, remove the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Jeep Commander or any other vehicle.
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.