There’s a likely probability you will need to replace your old and worn out spark plugs several times while you own a a 2000 Ford Contour. Spark plugs are one of the most vital components inside your engine as they trigger the entire combustion process that starts and keeps your engine running for many thousands of miles. Like most engine parts, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do yourself. Chances are, if you’ve found yourself here, you have no idea how to do that, or perhaps you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take roughly 20-45 minutes. This article will go over everything you will need to know about your Ford Contour’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2000 Ford Contour
Recommended 2.5L V6 2000 Ford Contour Spark Plugs
Recommended 2.0L L4 2000 Ford Contour Spark Plugs
These spark plugs are an exact fit for their respective engines and will match the required specifications. Make certain that you purchase the correct number of spark plugs for your engine corresponding to the number of cylinders. Occasionally manufacturers will bundle spark plugs in quantities that make it difficult to buy the exact amount you need for your engine. In this case, it can’t hurt to purchase enough for your next two spark plug changes just so you will always have a new set ready. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available in today’s market at a reasonable price.
How often should I change my spark plugs?
In general, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the specific interval determined by Ford for the 2000 Contour. Of course, if you drive your vehicle more aggressively or own a Ford Contour with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that may need a spark plug replacement early, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
Consider that this list is of course not comprehensive, and these problems on their own do not necessarily point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with regular maintenance, and you are definitely doing so with the responsible decision to replace your 2000 Ford Contour’s spark plugs on a regular basis.
Changing spark plugs on a 2000 Ford Contour
This is a process you should be able to do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM for short) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to do a spark plug change with some ordinary tools you probably already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some general tools that you should absolutely have in your toolbox if you don’t already.
- A torque wrench is a vital tool to have in your collection. You should check your factory service manual to determine the correct torque rating to use when inserting the new spark plugs for your 2000 Ford Contour to be certain they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the exact problem.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if this is not the case, you should definitely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it comes in handy for a decent number of other jobs.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
Tips for changing spark plugs on your 2000 Ford Contour
Be sure to reference the video above before you attempt to repair the spark plugs on your 2000 Ford Contour, as well as review your FSM (factory service manual) or owner’s manual. Be sure to check the tips shown here to help you as you complete this repair.
- Your engine should be completely cold before you replace your spark plugs. Wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 2000 Ford Contour
- First, remove the negative terminal of your battery. It’s a good idea to disconnect the battery anytime you work on the electrical system of your Ford Contour or any other vehicle.
- It isn’t a bad idea to use dielectric grease when installing new spark plugs. You can apply a a tiny amount to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- During this process, one of the most vital things to ensure you do is to avoid is overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- Note that this is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a tiny amount of anti-seize to the threads of their spark plugs, especially on older vehicles.