There’s a good probability you will need to replace your old and worn out spark plugs several times over the course of owning a 2010 Dodge Caliber. Spark plugs are one of the most vital parts inside your engine as they begin the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine components, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do on your own. Chances are, if you’ve found yourself here, you have no idea how to do that, or potentially you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you should need to know about your Dodge Caliber’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2010 Dodge Caliber
How often should I change my spark plugs?
Very generally, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the specific interval determined by Dodge for the 2010 Caliber. Of course, if you drive your vehicle more aggressively or own a Dodge Caliber with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that may potentially need a spark plug replacement prematurely, such as:
- Problems starting your engine
- Engine misfiring
- Rough idle
As a quick note, keep in mind that this list is certainly not comprehensive, and these problems on their own do not necessarily point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with organized maintenance, and you are definitely doing so with the responsible decision to replace your 2010 Dodge Caliber’s spark plugs on a regular basis.
Changing spark plugs on a 2010 Dodge Caliber
This is a process you should be able to do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM for short) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A torque wrench is a vital tool to have in your garage. You should check your FSM (factory service manual) to determine the correct torque rating to use when installing the new spark plugs for your 2010 Dodge Caliber to be sure they are installed properly.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and modify it if necessary. Most plugs will come pregapped, but if this is not the case, you should for sure have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit more straightforward to check the exact gap, and it is useful for a decent number of other jobs.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the definite problem.
Tips for changing spark plugs on your 2010 Dodge Caliber
- One of the most important things to remember is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- You should replace spark plugs on a cold engine. You should wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2010 Dodge Caliber
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a very light coating to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- Before starting, disconnect the negative terminal of your battery. It’s a good idea to disconnect the battery anytime you work on the electrical system of your Dodge Caliber or any other vehicle.