Maintaining your vehicle is an incredibly rewarding task and learning how to replace your spark plugs is a great place to start. There’s a likely chance you will need to replace your old spark plugs several times during your ownership of a 2010 GMC Savana 2500. Spark plugs are one of the most vital components inside your engine as they start the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine components, spark plugs experience wear over time and eventually need to be swapped out for new replacements, but fortunately this is a repair you can do on your own. Chances are, if you’ve found yourself here, you have no idea how to do that, or potentially you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you will need to know about your GMC Savana 2500’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2010 GMC Savana 2500
DENSO 4713[/caption]For any 2010 GMC Savana 2500, you can use DENSO 4713 spark plugs. These will be an exact fit and will match the required specifications of your engine. As this 2010 GMC Savana 2500 features an 8 cylinder engine, ensure you purchase 8 spark plugs. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available in today’s market at a reasonable price.
How often should I change my spark plugs?
Very generally, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by GMC for the 2010 Savana 2500. Of course, if you drive your vehicle more aggressively or own a Savana 2500 with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that may need a spark plug replacement earlier than the recommended schedule, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
Consider that this list is absolutely not comprehensive, and these problems on their own do not definitively point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with regular maintenance, and you are definitely doing so with the responsible decision to replace your GMC Savana 2500’s spark plugs on a regular basis.
Changing spark plugs on a 2010 GMC Savana 2500
This is a process you should be able to do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM for short) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A spark plug tester – this is definitely a niche tool, but it can save you a ton of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the exact problem.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A torque wrench is a essential tool to have in your toolbox. You will want to check your factory service manual to determine the correct torque rating to use when installing the new spark plugs for your 2010 GMC Savana 2500 to be confident they are installed properly.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if this is not the case, you should definitely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit more straightforward to check the exact gap, and it is useful for a decent number of other jobs.
Tips for changing spark plugs on your 2010 GMC Savana 2500
- During this process, one of the most vital things to ensure you do is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a tiny amount of anti-seize to the threads of their spark plugs, especially on older vehicles.
- You should replace spark plugs on a cold engine. Ensure you wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 2010 GMC Savana 2500
- You might consider using dielectric grease when installing new spark plugs. You can apply a a little bit to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- First, disconnect the negative terminal of your battery. It’s a good idea to disconnect the battery anytime you work on the electrical system of your GMC Savana 2500 or any other vehicle.