Spark plugs are one of the most critical components inside your engine that need to be maintained. There’s a likely probability you will be required to replace your set of spark plugs several times while you own a a 2012 Toyota Sequoia. Spark plugs are one of the most critical parts inside your engine as they start the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine components, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do on your own. Chances are, if you’ve found yourself here, you have no idea how to do that, or maybe you’d just like to know what kind of spark plugs you need to buy. The entire process of changing your spark plugs should take roughly 20-45 minutes. This article will go over everything you’ll need to know about your Toyota Sequoia’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2012 Toyota Sequoia
How often should I change my spark plugs?
In general, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Toyota for the 2012 Sequoia. Of course, if you drive your vehicle more aggressively or own a Sequoia with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that may potentially need a spark plug replacement prematurely, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
As a quick note, keep in mind that this list is certainly not comprehensive, and these problems on their own do not definitively point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with regular maintenance, and you are definitely doing so with the responsible decision to replace your Toyota Sequoia’s spark plugs on a regular basis.
Changing spark plugs on a 2012 Toyota Sequoia
This is a process you can do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A spark plug tester – this is definitely a niche tool, but it can save you a ton of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the exact problem.
- A torque wrench is a very important tool to have in your collection. You should check your FSM (factory service manual) or owner’s manual to determine the correct torque rating to use when putting in the new spark plugs for your 2012 Toyota Sequoia to be certain they are installed properly.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if not, you should absolutely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit more straightforward to check the exact gap, and it is helpful for quite a few other jobs.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Additionally, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
Tips for changing spark plugs on your 2012 Toyota Sequoia
- Your engine should be cold before you replace your spark plugs. Wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2012 Toyota Sequoia
- Note that this is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a small amount of anti-seize to the threads of their spark plugs, especially on older vehicles.
- First, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Toyota Sequoia or any other vehicle.
- One of the most important things to remember is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a small dab to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.