There’s a good probability you will need to replace your set of spark plugs several times over the course of owning a 2011 Honda CR-V. Spark plugs are one of the most critical parts inside your engine as they trigger the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine components, spark plugs experience wear over time and eventually need to be replaced, but fortunately this is a repair you can do yourself. Chances are, if you’ve found yourself here, you have no idea how to do that, or potentially you’d just like to know what kind of spark plugs you need to buy. The entire process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you’ll need to know about your Honda CR-V’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2011 Honda CR-V
How often should I change my spark plugs?
In general, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Honda for the 2011 CR-V. Of course, if you drive your vehicle more aggressively or own a Honda CR-V with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that needs a spark plug replacement early, such as:
- Problems starting your engine
- Rough idle
- Engine misfiring
Note that this list is of course not comprehensive, and these problems on their own do not definitively point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with organized maintenance, and you are definitely doing so with the responsible decision to replace your 2011 Honda CR-V’s spark plugs on a regular basis.
Changing spark plugs on a 2011 Honda CR-V
This is a process you should be able to do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A torque wrench is a vital tool to have in your garage. You will want to check your factory service manual to determine the correct torque rating to use when installing the new spark plugs for your 2011 Honda CR-V to be confident they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the exact problem.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and change it if necessary. Most plugs will come pregapped, but if not, you should absolutely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it is helpful for quite a few other jobs.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. In addition, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
Tips for changing spark plugs on your 2011 Honda CR-V
- Before starting, remove the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Honda CR-V or any other vehicle.
- You should replace spark plugs on a cold engine. Wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2011 Honda CR-V
- Take this (unofficial advice) lightly as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a tiny amount of anti-seize to the threads of their spark plugs, especially on older vehicles.
- During this process, one of the most vital things to ensure you do is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- You might consider using dielectric grease when installing new spark plugs. You can apply a a tiny amount to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.