Maintaining your vehicle is an incredibly rewarding task and learning how to replace your spark plugs is a great place to start. There’s a decent chance you will need to replace your old spark plugs several times while you own a a 2010 Toyota RAV4. Spark plugs are one of the most important components inside your engine as they start the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do yourself. Odds are, if you’ve found yourself here, you have no idea how to do that, or perhaps you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you’ll need to know about your Toyota RAV4’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2010 Toyota RAV4
AUTOLITE APP5325[/caption]For any 2010 Toyota RAV4, you can use AUTOLITE APP5325 spark plugs. These will be an exact fit and will match the required specifications of your engine. Make sure you purchase the correct number of spark plugs for your engine corresponding to the number of cylinders. Often, manufacturers will bundle spark plugs in quantities that make it difficult to buy the exact amount you need for your engine. In this case, it can’t hurt to purchase enough for your next two spark plug changes just so you will always have a new set ready. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at an affordable price.
How often should I change my spark plugs?
As a general recommendation, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Toyota for the 2010 RAV4. Of course, if you drive your vehicle more aggressively or own a RAV4 with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that needs a spark plug replacement prematurely, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
Note that this list is certainly not comprehensive, and these problems on their own do not definitively point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with regular maintenance, and you are definitely doing so with the responsible decision to replace your Toyota RAV4’s spark plugs on a regular basis.
Changing spark plugs on a 2010 Toyota RAV4
This is a process you can do on your own with some ordinary garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to complete a spark plug change with some regular tools you most likely already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some commonplace tools that you should definitely have in your toolbox if you do not already.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug gap tool. This allows you to check the gap of your spark plugs and increase or decrease it if necessary. Most plugs will come pregapped, but if this is not the case, you should absolutely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit more straightforward to check the exact gap, and it is helpful for a decent number of other jobs.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the definite problem.
- A torque wrench is a essential tool to have in your arsenal. You should check your factory service manual to determine the correct torque rating to use when installing the new spark plugs for your 2010 Toyota RAV4 to be certain they are installed properly.
Tips for changing spark plugs on your 2010 Toyota RAV4
Please make sure you review the video above before you attempt to repair the spark plugs on your 2010 Toyota RAV4, as well as review your FSM (factory service manual) or owner’s manual. Be sure to check the tips shown here to help you as you do this repair.
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- Your engine should be completely cold before you replace your spark plugs. Wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2010 Toyota RAV4
- Before beginning, disconnect the negative terminal of your battery. It is wise to disconnect the battery anytime you work on the electrical system of your Toyota RAV4 or any other vehicle.
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a very light coating to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- The most important thing is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.