There’s a good probability you will need to replace your old spark plugs several times during your ownership of a 2008 Ford Crown Victoria. Spark plugs are one of the most important parts inside your engine as they trigger the entire combustion process that starts and keeps your engine running for many thousands of miles. Like most engine parts and components, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do yourself. Odds are, if you’ve found yourself here, you have no idea how to do that, or maybe you’d just like to know what kind of spark plugs you need to buy. The entire process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you’ll need to know about your Ford Crown Victoria’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 2008 Ford Crown Victoria
For any 2008 Ford Crown Victoria, you can use CHAMPION 401 spark plugs. These will be an exact fit and will match the required specifications of your engine. As this 2008 Ford Crown Victoria features an 8 cylinder engine, ensure you purchase 8 spark plugs. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at a reasonable price.
How often should I change my spark plugs?
In general, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Ford for the 2008 Crown Victoria. Of course, if you drive your vehicle more aggressively or own a Crown Victoria with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that may potentially need a spark plug replacement earlier than the recommended schedule, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
Note that this list is certainly not comprehensive, and these problems on their own do not necessarily point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with routine maintenance, and you are definitely doing so with the responsible decision to replace your Ford Crown Victoria’s spark plugs on a regular basis.
Changing spark plugs on a 2008 Ford Crown Victoria
This is a process you can do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM for short) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to do a spark plug change with some regular tools you likely already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some commonplace tools that you should definitely have in your toolbox if you do not already.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug gap tool. This allows you to check the gap of your spark plugs and modify it if necessary. Most plugs will come pregapped, but if not, you should definitely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it is helpful for quite a few other jobs.
- A torque wrench is a essential tool to have in your toolbox. You should check your factory service manual to determine the correct torque rating to use when putting in the new spark plugs for your 2008 Ford Crown Victoria to be certain they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you a ton of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the exact problem.
Tips for changing spark plugs on your 2008 Ford Crown Victoria
Ensure you reference the video above before you attempt to repair the spark plugs on your 2008 Ford Crown Victoria, as well as review your factory service manual. Also, see the tips included below here to help you as you complete this repair.
- During this process, one of the most vital things to ensure you do is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a small amount to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- Note that this is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- Before beginning, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Ford Crown Victoria or any other vehicle.
- Your engine should be completely COLD before you replace your spark plugs. Ensure you wait at least 30 minutes after your engine has been running before attempting to replace the spark plugs on your 2008 Ford Crown Victoria