Spark plugs are one of the most critical components inside your engine that need to be maintained. There’s a decent probability you will need to replace your old and worn out spark plugs several times during your ownership of a 1998 Jeep Wrangler. Spark plugs are one of the most important components inside your engine as they trigger the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do yourself. Odds are, if you’ve found yourself here, you have no idea how to do that, or potentially you’d just like to know what kind of spark plugs you need to buy. The entire process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you should need to know about your Jeep Wrangler’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 1998 Jeep Wrangler
CHAMPION 9034[/caption]For any 1998 Jeep Wrangler, you can use CHAMPION 9034 spark plugs. These will be an exact fit and will match the required specifications of your engine. Ensure you purchase the correct number of spark plugs for your engine corresponding to the number of cylinders. Occasionally manufacturers will bundle spark plugs in quantities that make it difficult to buy the exact amount you need for your engine. In this case, it can’t hurt to purchase enough for your next two spark plug changes just so you will always have a new set ready to go. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at an affordable price.
How often should I change my spark plugs?
Very generally, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Jeep for the 1998 Wrangler. Of course, if you drive your vehicle more aggressively or own a Wrangler with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also telltale signs of a car that needs a spark plug replacement prematurely, such as:
- Engine misfiring
- Rough idle
- Problems starting your engine
Note that this list is of course not comprehensive, and these problems on their own do not definitively point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with organized maintenance, and you are definitely doing so with the responsible decision to replace your Jeep Wrangler’s spark plugs on a regular basis.
Changing spark plugs on a 1998 Jeep Wrangler
This is a process you can do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A spark plug gap tool. This allows you to check the gap of your spark plugs and change it if necessary. Most plugs will come pregapped, but if this is not the case, you should for sure have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit more straightforward to check the exact gap, and it is helpful for quite a few other jobs.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. In addition, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A torque wrench is a very important tool to have in your garage. You will want to check your FSM (factory service manual) to determine the correct torque rating to use when inserting the new spark plugs for your 1998 Jeep Wrangler to be certain they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you a ton of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the exact problem.
Tips for changing spark plugs on your 1998 Jeep Wrangler
- This is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- One of the most important things to remember is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.
- Your engine should be cold before you replace your spark plugs. Wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 1998 Jeep Wrangler
- Before you begin, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Jeep Wrangler or any other vehicle.
- You might consider using dielectric grease when installing new spark plugs. You can apply a a very light coating to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.