There’s a likely probability you will need to replace your set of spark plugs several times over the course of owning a 1996 Toyota T100. Spark plugs are one of the most vital components inside your engine as they begin the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts and components, spark plugs experience wear over time and eventually need to be swapped out for new replacements, but fortunately this is a repair you can do yourself. Chances are, if you’ve found yourself here, you have no idea how to do that, or perhaps you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take approximately 20-45 minutes. This article will go over everything you’ll need to know about your Toyota T100’s spark plugs, whether you need some baseline information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 1996 Toyota T100
For any 1996 Toyota T100, you can use NGK 7090 spark plugs. These will be an exact fit and will match the required specifications of your engine. Make sure you purchase the correct amount of spark plugs for your engine corresponding to the number of cylinders. Often, manufacturers will bundle spark plugs in quantities that make it impossible to buy the exact amount you need for your engine. In this case, it is a good idea to purchase enough for your next two spark plug changes just so you will always have a new set ready to go. We always try to recommend the best possible spark plugs for the money, and these spark plugs are either a factory recomendation or an equivalent replacement available now at an affordable price.
How often should I change my spark plugs?
Very generally, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the specific interval determined by Toyota for the 1996 T100. Of course, if you drive your vehicle more aggressively or own a Toyota T100 with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that may need a spark plug replacement earlier than the recommended schedule, such as:
- Rough idle
- Engine misfiring
- Problems starting your engine
Note that this list is of course not comprehensive, and these problems on their own do not definitively point to the spark plugs being the solitary culprit. However, the best way to prevent any issues with your vehicle is to take care of it with organized maintenance, and you are definitely doing so with the responsible decision to replace your 1996 Toyota T100’s spark plugs on a regular basis.
Changing spark plugs on a 1996 Toyota T100
This is a process you can do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
As noted before, you should be able to do a spark plug change with some ordinary tools you probably already have. However, there are a few tools that are specific to this job that you may not have, and we also want to recommend some general tools that you should absolutely have in your toolbox if you do not already.
- A spark plug gap tool. This allows you to check the gap of your spark plugs and change it if necessary. Most plugs will come pregapped, but if this is not the case, you should definitely have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it is helpful for countless other jobs.
- A torque wrench is a essential tool to have in your collection. You should check your factory service manual to determine the correct torque rating to use when putting in the new spark plugs for your 1996 Toyota T100 to be confident they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of an issue. This tool can help you diagnose the exact problem.
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. Also, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
Tips for changing spark plugs on your 1996 Toyota T100
Be sure to review the video above before you attempt to repair the spark plugs on your 1996 Toyota T100, as well as review your factory service manual. Also, see the tips included below here to help you as you perform this repair.
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a tiny amount to the inside of the boot and the ceramic part of your spark plugs. It lessens the chance of voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- Your engine should be cold before you replace your spark plugs. Ensure you wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 1996 Toyota T100
- First, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Toyota T100 or any other vehicle.
- Note that this is not official advice as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a light coating of anti-seize to the threads of their spark plugs, especially on older vehicles.
- During this process, one of the most vital things to ensure you do is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.