There’s a decent probability you will need to replace your worn out spark plugs several times during your ownership of a 1996 Chevrolet Blazer. Spark plugs are one of the most important components inside your engine as they trigger the entire combustion process that starts and keeps your engine running for many thousands of miles. Similar to most engine parts, spark plugs experience wear over time and eventually need replacement, but fortunately this is a repair you can do yourself. Chances are, if you’ve found yourself here, you have no idea how to do that, or maybe you’d just like to know what kind of spark plugs you need to buy. The complete process of changing your spark plugs should take about 20-45 minutes. This article will go over everything you will need to know about your Chevrolet Blazer’s spark plugs, whether you need some general information or a full, step-by-step guide to performing a spark plug change.
Correct spark plugs on a 1996 Chevrolet Blazer
How often should I change my spark plugs?
As a general recommendation, it is advised that you replace spark plugs once every 20,000 to 40,000 miles. Of course, please make sure to check your owner’s manual to determine the exact interval determined by Chevrolet for the 1996 Blazer. Of course, if you drive your vehicle more aggressively or own a Chevrolet Blazer with some modifications, you may want to consider changing your spark plugs closer to the 20,000 miles end of that spectrum.
However, there are also classic signs of a car that needs a spark plug replacement early, such as:
- Rough idle
- Problems starting your engine
- Engine misfiring
Consider that this list is certainly not comprehensive, and these problems on their own do not definitively point to the spark plugs being the standalone culprit. However, the best way to prevent any issues with your vehicle is to take care of it with routine maintenance, and you are definitely doing so with the responsible decision to replace your 1996 Chevrolet Blazer’s spark plugs on a regular basis.
Changing spark plugs on a 1996 Chevrolet Blazer
This is a process you should be able to do on your own with some commonplace garage tools. Of course, consult your owner’s manual, as well as a factory service manual (FSM for short) or an equivalent Haynes or Chiltons manual. The video shown below does a good job of outlining the process.
Helpful Tools
- A set of spark plug sockets – These come in extremely handy because many standard sockets are not deep enough for spark plugs. In addition, some spark plug holes are a bit smaller, so it requires a thinner wall like the one featured in the product here to fit. The linked product also features a magnet to keep a good hold of the spark plug so you do not drop it into your engine bay!
- A spark plug gap tool. This allows you to check the gap of your spark plugs and modify it if necessary. Most plugs will come pregapped, but if not, you should for sure have one of these.
- I also highly recommend you have a feeler gauge as it makes it a bit easier to check the exact gap, and it comes in handy for quite a few other jobs.
- A torque wrench is a essential tool to have in your toolbox. You should check your FSM (factory service manual) or owner’s manual to determine the correct torque rating to use when inserting the new spark plugs for your 1996 Chevrolet Blazer to be certain they are installed properly.
- A spark plug tester – this is definitely a niche tool, but it can save you lots of time. Although we’ve discussed spark plug replacement being a good thing to replace regularly and not just when issues occur, you may also be replacing your spark plugs because of something going wrong. This tool can help you diagnose the definite problem.
Tips for changing spark plugs on your 1996 Chevrolet Blazer
- Take this (unofficial advice) lightly as many spark plug manufacturers advise against the use of anti-seize. However, I have heard from numerous old-school mechanics that they always apply a small amount of anti-seize to the threads of their spark plugs, especially on older vehicles.
- Before starting, disconnect the negative terminal of your battery. You should always disconnect the battery anytime you work on the electrical system of your Chevrolet Blazer or any other vehicle.
- It’s not a bad idea to use dielectric grease when installing new spark plugs. You can apply a a very light coating to the inside of the boot and the ceramic part of your spark plugs. It prevents voltage leak and helps avoid the misfortune of the boot fusing to the spark plug over time.
- Your engine should be cold before you replace your spark plugs. Wait at least 30 minutes after any kind of operation before attempting to replace the spark plugs on your 1996 Chevrolet Blazer
- The most important thing is to avoid overtightening the plugs or worse, cracking them due to overtightenting. Use a torque wrench capable of lower, more precise torque ratings to be sure that you don’t make this mistake.